Fuerd  Precision offers Flexibility (Prototypes, Small Quantity Runs - 5 to 25 pieces at a time and High Volume), Service (Quick Responsive Lead times, On time Performance, and Superior Investment Casting Engineering Support), Quality (Mechanical component parts produced that meet if not exceed your requirements), Reduce Cost, and Single Source Responsibility (one source to provide your parts complete). From aluminum investment castings to low alloy investment castings to stainless steel investment castings, Fuerd  Precision has the alloy that will best meet your needs. Investment CastingsYour investment casting solution for cost reductions and enhanced part performance.Investment Castings reduce the High Cost of your machined parts, weldments, fabrications and assembled mechanical components by as much as 30 to 50%... From simple to complex shapes, Investment Castings provide you with the ideal solution to your low/medium quantity mechanical component requirements. Investment Casting BenefitsEnjoy the benefits of investment casting such as greater design freedom (complex intricate shapes easily cast - assemblies cast as one part), greater investment casting alloy selection (over 150 non ferrous and ferrous alloys to chose from to select an alloy that best suits your investment casting application), improved surface finishes and a greater opportunity for cost and weight reduction. Investment castings, also known as lost wax investment casting, will enhance the design and the performance of your mechanical component parts. Our investment castings are produced to precision tolerances of +/- .005 inch per inch and to machined like surfaces of 125 RMS.

we promise to provide you with aluminum die casting parts of the highest quality and at the best value. We can produce aluminum die casting parts with weights from 800mm. We inject the metal into the mold under high pressures of 10-210Mpa (1,450-30,500 psi). This results in a more uniform part with a good surface finish and good dimensional accuracy, (0.2% of casting dimensions). Post machining can be totally eliminated for most parts and in other cases only light machining is required to bring dimensions to the proper size. We use aluminum material of ASTM grade 380, 390, and aluminum alloy die-casting (ADC12 and ADC14). We can produce parts such as automotive engine house covers, light covers, various housing assemblies and more.Our factory have Large spectrum of die casting machines (280T - 1600T),it can produce Variety of alloys available to meet in house production requirements and to provide quality custom-made die-casting parts for other industries. Aluminum Die Cast Parts produced by FUERD Die Casting Company can be stronger than steel. FUERD Die Casting Company is a part diecaster of lower priced, better quality aluminum die cast parts, sometimes also known as castings, aluminum part castings, high pressure part die castings, or aluminum diecastings. FUERD Die Casting has Low Quantity Die Casting Production or High Quantity Die Casting Part Production. High pressure die casting is a process we use to make aluminum die cast parts. We inject molten aluminum alloy metal under pressure into a steel die to produce aluminum parts. Diecasting is a very inexpensive aluminum part manufacturing process. Primarily we produce aluminum alloy die castings, but we also make some diecastings in zinc alloys. FUERD Die Casting Company's die cast design consultants will assist you with die casting aluminum part design, aluminum die casting prototypes, die cast tooling, machining of die cast parts and finish the surface of many kinds of die cast aluminum parts. Aluminum die casting is the process of forcing molten metal under pressure into metal molds or dies. It is one of the most economical and effective methods of producing moderate to high-volume quantities of parts. There are three main requirements for producing commercially acceptable aluminum die casting parts. They are: An efficient aluminum die casting machine.Suitable casting alloy. The equipment needed to produce the parts are essentially the molds and an aluminum die casting machine that holds, opens and closes the molds or dies. The variables that determine the surface quality and consistency of the parts are directly related to the die itself. The die must possess the quality of thermal balance (heat input vs. heat extraction) this controls surface quality, soundness of the part and dictates cycling speed. The three main variables that affect the quality of the aluminum die cast part are: Die design   Die material  Die production methodFinishing processes.

Fundamentally, a mold is produced by shaping a refractory material to form a cavity of a desired shape such that molten metal can be poured into the cavity. The mold cavity needs to retain its shape until the metal has solidified and the casting is removed. This sounds easy to accomplish, but depending on the choice of metal, certain characteristics are demanded of the mold. Green Sand Molding The most common method used to make metal castings is green sand molding. In this process, granular refractory sand is coated with a mixture of bentonite clay, water and, in some cases, other additives. The additives help to harden and hold the mold shape to withstand the pressures of the molten metal. The green sand mixture is compacted through mechanical force or by hand around a pattern to create a mold. The mechanical force can be induced by slinging, jolting, squeezing or by impact/impulse. The following points should be taken into account when considering the green sand molding process.

Fundamentally, a mold is produced by shaping a refractory material to form a cavity of a desired shape such that molten metal can be poured into the cavity. The mold cavity needs to retain its shape until the metal has solidified and the casting is removed. This sounds easy to accomplish, but depending on the choice of metal, certain characteristics are demanded of the mold. Green Sand Molding The most common method used to make metal castings is green sand molding. In this process, granular refractory sand is coated with a mixture of bentonite clay, water and, in some cases, other additives. The additives help to harden and hold the mold shape to withstand the pressures of the molten metal. The green sand mixture is compacted through mechanical force or by hand around a pattern to create a mold. The mechanical force can be induced by slinging, jolting, squeezing or by impact/impulse. The following points should be taken into account when considering the green sand molding process.

In these systems, sand is mixed with one or two liquid resin components and a liquid catalyst component. As soon as the resin(s) and catalyst combine, a chemical reaction begins to take place that hardens (cures) the binder. The curing time can be lengthened or shortened based on the amount of catalyst used and the temperature of the refractory sand. The mixed sand is placed against the pattern or into the corebox. Although the sand mixtures have good flowability, some form of compaction (usually vibration) is used to provide densification of the sand in the mold/core. After a period of time, the core/mold has cured sufficiently to allow stripping from the corebox or pattern without distortion. The cores/molds are then allowed to sit and thoroughly cure. After curing, they can accept a refractory wash or coating that provides a better surface finish on the casting and protects the sand in the mold from the heat and erosive action of the molten metal as it enters the mold cavity.

In-house finishing processes are Trimming, Shotblasting, Vibro-deburring, Anodizing and Vacuum Impregnation. We also have in-house mechanised washing machine & a dedicated leaktest machine for the castings to be leaktested. Subcontracted processes are Powder coating, Lacquering,  & Chromotizing. the product range. Lamp Cover (investment casting), front cover of electromotor(investment casting), Manufacturer , Alloy Casting investment , Zinc investment Casting , Aluminum Aluminum Casting investment , TV Wall MountS(Television Mounts) , Aluminum Custom investmentcast , Alloy Casting investment , Aluminum Pressure investment accessories, Chair Parts, Air compressor Parts, accessories, Manhole cover parts.

In-house finishing processes are Trimming, Shotblasting, Vibro-deburring, Anodizing and Vacuum Impregnation. We also have in-house mechanised washing machine & a dedicated leaktest machine for the castings to be leaktested. Subcontracted processes are Powder coating, Lacquering,  & Chromotizing. the product range. Lamp Cover (investment casting), front cover of electromotor(investment casting), Manufacturer , Alloy Casting investment , Zinc investment Casting , Aluminum Aluminum Casting investment , TV Wall MountS(Television Mounts) , Aluminum Custom investmentcast , Alloy Casting investment , Aluminum Pressure investment accessories, Chair Parts, Air compressor Parts, accessories, Manhole cover parts,.

we promise to provide you with aluminum die casting parts of the highest quality and at the best value. We can produce aluminum die casting parts with weights from 800mm. We inject the metal into the mold under high pressures of 10-210Mpa (1,450-30,500 psi). This results in a more uniform part with a good surface finish and good dimensional accuracy, (0.2% of casting dimensions). Post machining can be totally eliminated for most parts and in other cases only light machining is required to bring dimensions to the proper size. We use aluminum material of ASTM grade 380, 390, and aluminum alloy die-casting (ADC12 and ADC14). We can produce parts such as automotive engine house covers, light covers, various housing assemblies and more.Our factory have Large spectrum of die casting machines (280T - 1600T),it can produce Variety of alloys available to meet in house production requirements and to provide quality custom-made die-casting parts for other industries. Aluminum Die Cast Parts produced by FUERD Die Casting Company can be stronger than steel. FUERD Die Casting Company is a part diecaster of lower priced, better quality aluminum die cast parts, sometimes also known as castings, aluminum part castings, high pressure part die castings, or aluminum diecastings. FUERD Die Casting has Low Quantity Die Casting Production or High Quantity Die Casting Part Production. High pressure die casting is a process we use to make aluminum die cast parts. We inject molten aluminum alloy metal under pressure into a steel die to produce aluminum parts. Diecasting is a very inexpensive aluminum part manufacturing process. Primarily we produce aluminum alloy die castings, but we also make some diecastings in zinc alloys. FUERD Die Casting Company's die cast design consultants will assist you with die casting aluminum part design, aluminum die casting prototypes, die cast tooling, machining of die cast parts and finish the surface of many kinds of die cast aluminum parts. Aluminum die casting is the process of forcing molten metal under pressure into metal molds or dies. It is one of the most economical and effective methods of producing moderate to high-volume quantities of parts. There are three main requirements for producing commercially acceptable aluminum die casting parts. They are: An efficient aluminum die casting machine Suitable casting alloy. The equipment needed to produce the parts are essentially the molds and an aluminum die casting machine that holds, opens and closes the molds or dies. The variables that determine the surface quality and consistency of the parts are directly related to the die itself. The die must possess the quality of thermal balance (heat input vs. heat extraction) this controls surface quality, soundness of the part and dictates cycling speed. The three main variables that affect the quality of the aluminum die cast part are: Die design   Die material  Die production method Finishing processes.